Showing results: 766 - 780 of 1587 items found.
-
56XS1 -
North Atlantic Industries
NAI’s 56XS1 is a conduction-cooled, 2,000 Watt AC/DC Power Supply that converts either 3-phase, AC input or +270 VDC input into a single DC output at 2,000 Watts.
-
STMicroelectronics
ST’s STSPIN drivers for 3-phase brushless DC (BLDC) motors includes power drivers in a 3-phase bridge configuration and integrated solutions with built-in decoding logic for Hall-effect sensors.
-
cBP-6418U -
ADLINK Technology Inc.
*1 Segment: 1 system + 7 peripheral slots*cPCI BUS: up to 64-bit/66MHz*Power connectors: ATX connector x 1 DC Screw terminals
-
Carl E. Holmes Company
Shown below is an Electrochlorination power supply with a 4/20 ma interface. Input is 240 VAC, 1 PH, 60 Hz. Output is 0 to 10.5 DC, 130 Amps. This power supply can be interfaced with a PLC system. These units are custom units, built to order.
-
Model 50/12 -
TREK, INC.
The Model 50/12 is a DC-stable, high-voltage power amplifier featuring an all solid-state design for high slew rate, wide bandwidth, and low-noise operation. It is designed to provide precise control of output voltages in the range of 0 to ±50 kV DC or peak AC with an output current range of 0 to ±12 mA DC or peak AC.
-
FAD-100 -
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Long Time Record of Measurement by Input Power Supply・Detection of Both AC Current and DC Current At Once・Detection of Small DC current Inside Large AC Current・Freely Bending with Flexible Clamp Sensor of Inside Diameter 200mm・Useful for difficult Access Locations with Wide Ranges up to AC/DC 1000A
-
663xx Series -
Keysight Technologies
Use this family of specialized DC power sources to test your digital wireless appliances. All models offer DC sourcing, current sinking, fast transient response, GPIB, and measurement capabilities to help you with the unique challenges of simulating batteries and battery packs and measuring the current drawn by your device under test.
-
cPS-H325/110 -
ADLINK Technology Inc.
*PICMG® 2.11 CompactPCI® Power Interface compliant*Internal OR-ing Diodes for N + 1 redundancy*PICMG® 2.11 47-pin CompactPCI® in-rack power module interface*250 W DC output*Active PFC (Power Factor Correction) meets IEC1000-3-2 Harmonic Correction
-
SWTS -
Xi'an Multipower Technic Co.,LTD
SWTS switchgear intelligent test system is the fruit of many-year research and development by experts from our company. It includes all functions of SWT-IIIA?SWT-IIIB and SWT-IIIC and installs the various internal power supplies (Spring DC, Spring AC and electromagnetism operating mechanism power supply) in the system to directly define the power output.
-
677B -
TREK, INC.
The Trek Model 677B is a high-voltage power amplifier/supply unit for precise control of output voltages in the range of 0 to ±2 kV DC or peak AC with an output current range of 0 to ±5 mA DC or peak AC. The Model 677B can be operated in one of two modes: as a high-voltage amplifier where it is configured as a noninverting amplifier with a fixed gain of 200 V/V, or as a high-voltage power supply which responds to front panel controls to command an exact output voltage or current.
-
PeakTech Prüf- und Messtechnik GmbH
A DC switching power supply, which convinces with its high performance and best price / performance ratio. The switching power supply technology used ensures high performance with a small size and low weight. 6 different DC output voltages (3 V / 4.5 V / 6 V / 7.5 V / 9 V and 12 V) can be set using a slider. With the 4 mm pole terminals, you can easily connect single wires but also 4 mm banana plugs.
-
Model 603 -
TREK, INC.
The Trek Model 603 is a DC-stable, Power Amplifier/Piezo Driver designed to provide precise control of output voltages in the ranges of 0 to ±125 V, 0 to -250 V, or 0 to +250 V DC or peak AC. The output current capability is 0 to ±40 mA DC or 0 to ±80 mA peak AC for all voltage ranges
-
Series MSK -
Kepco, Inc.
Kepco's MSK linear power supplies provide a selection of five models, offering 100 Watts of stable benchtop power. They use a high gain linear (series pass) stabilizer circuit for ultra low noise and low ripple output, good stability, and accurate resettability, and they are MIL-STD-461 compliant.MSK's "Preview" switch (d-c on-off) allows voltage and current to be pre-set with the digital meters displaying the set values. At "d-c off," no voltage is applied to the output terminals and no load current needs to be drawn to set the current limit. At "d-c on," the set voltage is applied to the output terminals, the appropriate mode indicator illuminates and the meters indicate actual voltage and current.
-
Keysight Technologies
Measure voltage, current and power on 4 channels: DC, 1-phase AC or 3-phase ACMake more accurate power measurements: 0.05% at 50/60 HzMeasure current directly: internal shunts to 50 Arms, or with external probes or transducersAddress multiple test scenarios with isolated inputs
-
786848-01 -
NI
The CC5002X, or Hioki 3275, is a clamp-on current probe that offers a wide DC to 2 MHz bandwidth and 500 A of continuous input. It is ideal for capturing transient current signals from switching power supplies, inverters, and motor controllers. The probe requires an external power supply.